Ceramic Allround Coating Koch Chemie C0.02, 75ml
Review: 5 - "A masterpiece of literature" by , written on May 4, 20020

Ceramic Allround Coating Koch Chemie C0.02, 75ml

Available: Out of Stock
  • Product SKU: 506001


Ceramic Allround Coating Koch Chemie C0.02, 75ml is a ceramic layer that can be used on a variety of surfaces to provide long-lasting protection. The very thin protective layer is permanently attached to the surface by a chemical reaction. This chemical reaction is triggered by air humidity. The complete hardening is done after approx. nine days. Ceramic Allround Coating Koch Chemie C0.02, 75ml creates a very hydrophobic surface with very advanced rolling properties. The nature of the chemical properties makes the treated surface easy to clean by hand. The glossy finish obtained is preserved even after the use of acidic and alkaline detergents. The final sealing of the ceramic layer protects the paint from environmental influences, such as UV radiation, road salt, bird droppings and rust film, as well as reducing mechanical damage, making a significant contribution to maintaining or increasing the value of the vehicle.

Prior to polishing and sealing, thoroughly clean or wash the vehicle with an alkaline solution (eg, with Koch Chemie Green Star, 1000ml in a 1:10 dilution). In the case of coarse dirt such as tree resin, rust, tar, etc., pre-treat with cleaning clay, red or blue, wash tar A or similar.

Depending on the condition, the preparation of the varnish with strong or medium weather is done mechanically with Abrasive Polish Paste Koch Chemie Heavy Cut H9.02, 1L or Koch Chemie Fine Cut F6.01, 1000ml. The processing of slightly damaged varnishes and the removal of the hologram after polishing with Heavy Cut H9.01 or Fine Cut F6.01 is done with Koch Chemie Micro Cut M3.02, 1000ml with the help of Rupes Bigfoot LHR 15 Mark III, Orbital Polish.

Completely remove polishing residues with a polishing and sealing towel. Wipe all surfaces with a clean polishing and sealing towel, soaked in silicone and wax detergent or spray to prepare the panels, using a little pressure, and wipe with another second-hand polishing and sealing towel, just before drying. . This is the only method of complete removal of stresses, drying aids, oils contained in varnishes, etc. and to avoid adhesion problems of Ceramic Allround C0.02.

Caution: For solid or single-layer sensitive paints, silicone and removal wax should be diluted 1: 4 with water, preferably distilled water, to avoid possible matting. Lightly polish any residual streaks with another clean towel for polishing and sealing, without applying pressure. The paint should now have a scratch-free surface and no holograms in sunlight or a paint control lamp. After this step, the paint must not be touched with the palms / fingers (danger of adhesion problems, use gloves). The surface is now perfectly prepared for Ceramic Allround C0.02. For application, place the application cloth over the applicator block. Wet the entire surface of the application towel with Ceramic Allround C0.02 and quickly spread it over the layer. Wet the entire surface of the closed liquid film A must be visible. After applying two coats (two strips lengthwise and two crossbars), allow the product to dry for about 6-8 minutes and then immediately polish with the included towel. First remove the excess and then polish with the fresh part of the canvas with circular movements from outside to inside without pressure. Check the result with a paint control lamp to make sure it has no waves. Consumption per car approx. 15 - 20 ml.

Important notes on use: Before use, please read the danger warnings on the outer container or box and take appropriate protective measures. Ceramic Allround C0.02 reacts with air humidity. This can cause crystals to form on the edge when the glass is opened. If these crystals reach the application cloth, the surface to be covered is scratched. Therefore, the crystals must be wiped with a cloth before the product is dropped on the application towel. If Ceramic Allround C0.02 becomes "harder" during application, too little material has been used and more material must be applied. For double coatings, a drying time of approx.: After the first coating, 45 minutes must be observed. The coating is weather resistant after 18-24 hours. Perform a first car wash after nine days at the earliest, because the sealing material is only then completely dry. However, in the first nine days, bird droppings and insect debris should be removed quickly and easily. Cleaning agents with pH values ​​below 5 or above 12 should be avoided.

Car wash: Manual washing is recommended to keep the ceramic surface shiny for as long as possible. Use Green Star (1:10 dilution) for alkaline cleaning. Use Koch Chemie GSF Gentle Snow Foam, 1000ml.

Subsequent care: A professional subsequent care preserves the ceramic coating and minimizes water stains. For this reason, Auto Liquid Wax Koch Chemie PW ProtectorWax, 1000ml (1: 100 dilution) is recommended as a wet sealant after washing the car or Auto Spray Sealant Koch Chemie S0.02 Spray Sealant, 500ml as topper. Please refer to the product information for exact processing.

Quantity: 75ml